Home > Exchange 2010 > Unable To Relay Exchange Server 2010

Unable To Relay Exchange Server 2010

Contents

This comment has been removed by the author. Some extra information: We have had the server with Exchange 2003 shut down for a few weeks to see what would happen. http://blogs.technet.com/b/exchange/archive/2006/12/28/3397620.aspx Thanks. Reply Paul Cunningham says June 11, 2011 at 9:37 pm Ok so if you create a relay connector and set it so just the IP of the server can use it have a peek at this web-site

If i use port 25 for SMTP I get a generic 550 error from the barracuda device, So to avoid more confusion I just bypassed it as for network architecture there If you have this issue, try adding them until you get the one that fixes it for you. says February 5, 2013 at 5:22 am Figured it out. I had got as far as needing a recieve connector but no mix of settings worked, but these did.

550 5.7.1 Unable To Relay Exchange 2010 Smtp

Thanks. After few hours of troubleshooting, found out it was actually due to the Group Type in AD. However, when I run the normal process in SharePoint, it did not return any email. If so then I'd say that trend4.trendservices.inc is theirs.

By the sounds of it you have not created a Send Connector to route outbound email from Exchange 2010, therefore it takes the only available route which is via the Exchange The server response was: 550 5.7.1 Unable to relay Error: IMessage::Send - cdoNTLM, 0x80040211, The message could not be sent to the SMTP server. Some extra information: We have had the server with Exchange 2003 shut down for a few weeks to see what would happen. Ms-exch-smtp-accept-any-recipient I have an Windows SBS 2011 server running Exchange 2010.

Fix Exchange Errors & Restore All Mailboxes with Microsoft Exchange Recovery Software How to resolve the error '550 5.7.1 Unable to Relay' For Exchange 2003: If you have been using any 550 5.7.1 Unable To Relay Exchange 2013 External Reply Consultant says April 12, 2013 at 7:10 pm Thanks Paul Reply Christopher Hughes says April 11, 2013 at 1:30 am Hello Mr. Thanks for all your help, Christopher Hughes Reply Paul Cunningham says September 24, 2013 at 9:29 pm This is not really related to the topic of this article. Also go to http://www.testexchangeconnectivity.com and run the inbound email test.

Outgoing email from Exchange 2010 depends on a Send Connector. Exchange 2010 Receive Connector Reply Juan says September 17, 2013 at 7:53 am Excelente documento, me ayudo a aclarar mis dudas sobre este tema. You say "Sharing IP's works but is not best pratice". I think you'll be fine but of course you should keep an eye on it after making the change just in case something else causes a problem.

550 5.7.1 Unable To Relay Exchange 2013 External

Any ideas? we also reference here if anyone needs it. 550 5.7.1 Unable To Relay Exchange 2010 Smtp If a spammer sends an email to your network with a spoofed From address, and your server tries to send back an NDR but can't because the domain or email address 550 5.7.1 Unable To Relay Exchange 2010 Imap Home About Books Training Podcast Advertise Contact Practical 365  Exchange Server ProOffice 365 and Exchange Server News - Tips - Tutorials Exchange 2016 Exchange 2013 Office 365 PowerShell SSL Certificates

This weekend I changed our spam filtering service to McAfee SaaS Email Protection & Continuity, but they are not allowing me to use the outgoing service because they detect an open Check This Out Could I still implement this even though we use Postini as a smarthost? Reply Lucas says July 14, 2011 at 10:37 pm Thanks for the Tutorial, Paul. I have seen issues in the past when custom receive connectors contain the IPs of the Exchange Servers. Exchange 2010 Allow Smtp Relay Authenticated Users

Reply Warren says November 24, 2011 at 6:36 am Thanks - saved me hours! Once this all is done, you can now relay JIRA's emails via Exchange. The problems mainly arise with adding other Hub Transport IP's to a custom connector. Source Finally, thanks to your article, our Reporting Server can send emails to external users through our main Exchange 2010 server!!

I am assuming I am still missing a step? Exchange 2010 Relay Logs We have two HTs on seperate servers. Protocol logging shows that i am hitting the right receive connector but destination is show 127.0.0.1!!!

However with exchange 2010 and the new security concerns, we would like to achieve the following: Can you pl help me with the required configuration that we need to do?

one is using IIS smtp, another proprietary smtp dll, another vendor system- who knows. Start Exchange Server Manager. Reply Robert Anderton says June 15, 2011 at 7:14 pm Hi Paul, This seems to have sorted it. Exchange 2013 Allow Relay To External Domain I set this up on our servers this morning.

So instead of thinking of them as "Exchange Servers" think of it as a group of permissions that allows another host to do certain things. Reply SeanC says January 27, 2012 at 12:36 pm Hi Paul Great Article and your solution was just what i was after. For anyone who reads this later, the expected 220, actual 500 error was fixed by altering the authentication settings for the internet receive connector in exchange 2010. have a peek here How can I config on Receive Connector to restrict the internal anonimous smtp access?

Exchange Servers is required for relay (eg an app or device relaying mail to an external domain via your server). Its people like you that make Microsoft bearable. Reply Robert Anderton says June 15, 2011 at 7:14 pm Hi Paul, This seems to have sorted it. Reply Robert Anderton says June 9, 2011 at 6:42 pm Paul We are having the relay issue on a program that send messages to our clients, but we are on a

If you have servers/apps that can do basic auth then you can try configuring them to use the Client Receive Connector (runs on a different port) or configure a dedicated receive Reply Evan says June 13, 2012 at 4:25 am Hi Paul (and others), Dumb question: when configuring the "remote sending device" (in my case its an in-house Linux server that emails I'll give it a shot and keep an eye on things. Reply Paul Cunningham says November 17, 2014 at 9:30 am You'll need to describe in more detail what you're trying to achieve.

Non of those would flow until I setup the relay and told Exchange those specific IP addresses were OK to send mail. If your iPhone users are using SMTP to send email, and they are doing so from outside of the corporate firewall, I suspect you may have set up an open relay Would this then also mean that our server is pretty much open to relay from any source? The reason to un-tick Anonymous user is due to remote user connect to our Exchange Server and spam us.

We have a new linux server providing database and other services for a new enterprise resource app and it needs to email from within our enterprise. Reply Christopher Hughes says September 19, 2013 at 11:09 pm Hello Mr. some information about my current situation. HTH Reply Jason Hauck says November 2, 2012 at 2:14 am Thanks for the article.

This is obviously unacceptable and a secure method is needed.