Home > Unable To > Unable To Register To Dmi Service Layer

Unable To Register To Dmi Service Layer

To update the MIF on NetWare, instead of "load ciodmi" type "load ciodmi r". Database Reinitialized." If only a specific record in the log is found to be in error, the log will continue to report all valid records. At the time of this release, Novell is planning a NetWare 5.0 Support Pack update to avoid the message. The specific cases where this occurs are when the following two conditions are met: A Reconstruct, Verify or Initialize activity is running on the server, and The user opens the Activity http://mixtecadigital.com/unable-to/unable-to-register-service.html

If different, then change those values in the above URL)This should load the WSDL for the service in your web browser.If you are still facing issues after trying these two steps, If so, turn it off by additionally inserting the line as the last entry in your AUTOEXEC.NCF file. The event will state that an array member is down, but will reference the device ID of the spare. Similarly, if an array goes offline due to multiple drive failures, then following reactivation, the system must be rebooted to bring the array back on-line.

Thanks for posting.Like • Show 0 Likes0 Actions GregMesser Mar 3, 2015 5:36 PMAnother reason you get this message is when the service did not start successfully usually because the repository If the command fails, CI/O will post an error message. Note that you need to have Data Finder Administrator privileges in order to do so. 1. 1. Generated Fri, 23 Dec 2016 04:49:47 GMT by s_ac16 (squid/3.5.20)

If using an Ultra-2 SCSI host adapter with the FMS v3.01 (or later) drivers for NetWare, be sure that the NWASPI.CDM driver is also loaded. This can be an issue when the repository lives on the same server as Datafinder. Multiple events may otherwise be generated. As a temporary workaround, insert the following as the first line in your STARTUP.NCF file: set display relinquish control alerts = off Note that certain other applications may ensure that this

Please turn JavaScript back on and reload this page.All Places > DevTest Community > Discussions | Appears in 1 other placeLog in to create and rate content, and to follow, bookmark, It should be possible to determine whether this situation has occurred by viewing the contents of the event log. Join your peers on the Internet's largest technical computer professional community.It's easy to join and it's free. SUPPORT OF nStor ENCLOSURES Certain models of nStor CR8e enclosures are not supported.

Close Box Join Tek-Tips Today! Red Flag This Post Please let us know here why this post is inappropriate. We would really like to get DMI working properly, as I understand it's needed for Inventory to pull the Asset Tag info out of the BIOS. If all disk drives connected to the Array1000 controller's channels are members of a single array, and that array goes off-line, then the CI/O display will change.

Other values cannot be supported. Your cache administrator is webmaster. For example: Client X Server Y The timezone is PST EST Local Time 08:00 am 11:00 am Activity Scheduled for 07:00 pm for server y Activity Executed at 04:00 PM Already a member?

Loading ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection to 0.0.0.10 failed. Check This Out CI/O VERSION DEPENDENCIES IN CONNECTING CLIENTS TO SERVERS CI/O v1.0 is incompatible with the CI/O v4.x release. Installing the Novell NetWare components of CI/O to a server with a very large SYS volume (>2 Gbytes) may result in a low disk space error message. It can be viewed athttp://www.ca.com/us/services-support/ca-support/ca-support-online/knowledge-base-articles.tec1766582.htmlLike • Show 0 Likes0 Actions Related ContentRetrieving data ...Recommended ContentAction Pack JbossCould any one explain the attribute Distributed Target (Total) in Benefit: Portfolio Benefit Totals in

When upgrading CI/O to a newer version, make sure to update the corresponding DMI MIF or SNMP MIB to the same level. Use the Services screen to locate the Grid-Tools TDoD Service and set startup mode to Automatic (Delayed Start)This gives the Repository a chance to get going before TDoD tries to connect. USE OF CI/O WITH ARRAY1000 CONTROLLERS Previously-used drives should be freshly formatted or initialized before being connected to the Array1000 controller. http://mixtecadigital.com/unable-to/unable-to-register-service-soa.html The time now is 05:49 AM. 2016 Micro Focus Novell Documentation Novell Documentation is best viewed with JavaScript enabled.

Home Skip to Content Attachmate Borland Micro Focus Novell NetIQ Micro Focus Forums Today's Posts Mark All Forums Read Forum New Posts FAQ Calendar Community Groups Member List Forum Actions Mark This can be ignored. For each of the following, change the entry from Automatic to Manual, and then stop each service: CIO Array Management Service CIOArrayManager RPC Command CIOArrayManager RPC Event Start the SCSIDMI service

I have verified the service status, it was set to Running.Please help.Like • Show 0 Likes0 Actions Sameer_Chandragiri Nov 21, 2016 4:55 PMHi Raju,Can you confirm that the value of Primary

Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework. I am using 3.6.100.30 version. New features include: Cache management for all supported RAID levels Cache optimization wizard Automatic installation of ASPI drivers for monitoring SCSI host adapters (Windows NT and NetWare) FEATURES NO LONGER SUPPORTED Reactivation of an off-line array may only be performed in certain situations.

Support Pack fixes are already available for NetWare 4.11. Resources Join | Advertise Copyright © 1998-2016 ENGINEERING.com, Inc. Those models which include a dual SCSI bus architecture and SAF-TE enclosure management have been found to cause system errors. have a peek here Submit Contact our Support Team Request Case Start Chat Questions or issues with the site?

Then, a new log file "iomgr.log" will be created and subsequent events entered to that new file. This can occur when various other applications are installed on the server. Has anyone seen this before? Since the index exists but there are no indexed values, a SRID cannot be obtained.