Home > Unable To > Unable To Relay Error Message

Unable To Relay Error Message

Contents

In the Outbound connectors section, select the connector that's used for hybrid, and choose Edit. It can happen if the recipient doesn't allow relay, then the sender will not be able to reach or that the receiver domain is restricting the sender domain from relaying the Select the checkbox ‘Allow all computers which successfully authenticate to relay, regardless of the list above‘. Subject: Need of below system details. have a peek at this web-site

Add permission for the Anonymous account to public folders. Nobody's going to find a name in a .local TLD outside your own company. --- Rich Matheisen MCSE+I, Exchange MVP --- Rich Matheisen MCSE+I, Exchange MVP Wednesday, November 24, 2010 3:05 Yes, I know, windows is supposed to automagically defrag for you. When I checked the logs I saw the computer account authenticating.

550 5.7.1 Unable To Relay Exchange 2010

Most email providers don't care who uses thier SMTP server to send a message to somebody in the same domain, so it may look like everything is working until you try If not, make the smtp address for the organisation the primary, wait about 15 minutes and send the user an email - see if that comes back with the same error. My situation was that the e-mails were delivered to users who had access to send e-mail outside our network ([email protected]) but got the following error message for internal e-mail users ([email protected]) Thanks!   Your message did not reach some or all of the intended recipients.         Subject:                   Sent:                 1/25/2008 9:21 PM   The following recipient(s) could not be reached:  

I have change the IIS SMTP ip also through which this mail flow IP is 127.0.0.1 .Tell now I am getting this below error message . The company I work for has an 03 Exchange server, with POP3 setup on it. 1 part of our company is setup POP3. For more information on this issue, see the Microsoft Knowledge base article: Setting or Removing Relay Restrictions from a Virtual Server * If you are running an SMTP server on a Server Error '550 5.7.1 Unable To Relay' Outlook 2013 This software doesn't only repair the Exchange EDB file but also offer a preview of the user mailbox items such as emails, attachments, contacts, calendar, tasks etc.

Before i never worked with exchange. 550 5.7.1 Unable To Relay Exchange 2013 This can have serveral causes: * The emailhost parameter has not been specified correctly or not at all in the SAS configuration file. * If you run email in a stored Get-ReceiveConnector "Replace with your connector name" |Add-AdPermission -User "NT AUTHORITY\ANONYMOUS LOGON" -ExtendedRights ms-Exch-SMTP-Submit,ms-Exch-SMTP-Accept-Any-Recipient,ms-Exch-Bypass-Anti-Spam This Should help! -Mike Proposed as answer by Mohd. But it didn't for me.

Why was this unhelpful? Server Error '550 5.7.1 Unable To Relay' Outlook 2010 http://goo.gl/jNtfGI Reply Anonymous says: December 23, 2016 at 4:57 am Hello, I have the same problem with a single domain name that my users and servers seem to be sharing: the problem too from Outlook 2003 trying to SMTP through POP.  I tried every possible recommendations but to no avail - even recommendations here.   Then, I chance upon this advice from I haven't ever had the problem myself and the users haven't given me any follow up information on this problem.

550 5.7.1 Unable To Relay Exchange 2013

In that case, you should either: 1) Recreate the 'default' SMTP Receive connectors 2) Examine the output of 'get-adpermission ' to determine the different sets of permissions Tuesday, January 30, 2007 1:29 PM 2 Sign in to vote Hi! 550 5.7.1 Unable To Relay Exchange 2010 i added the site to "trusted sites" in IE and now it is sending emails. 550 5.7.1 Unable To Relay Office 365 Friday, October 06, 2006 5:12 AM 0 Sign in to vote I keep getting this same problem popping up from time to time.

Subject: test mail 11:43 Sent: 5/23/2009 12:57 PM The following recipient(s) could not be reached: '[email protected]' on 5/23/2009 12:57 PM 550 5.7.1 Unable to relay I saw good decision for my Check This Out and also we dont have firewall here..thanks for your reply.. Saturday, February 19, 2011 5:05 AM 0 Sign in to vote Since it seems this is an ongoing issue... Can anyone please help? 550 5.7.1 Unable To Relay Exchange 2007

Thursday, March 11, 2010 9:50 AM 0 Sign in to vote I've had situations where SMTP sending wasn't working with "Client cannot send as this user" error. When your done guessing, check out the "More Settings" button, especially that "Advanced" tab that allows you to open 25 mailboxes on the Exchange server, or more if you desire and For more information about verifying your SPF record, see Customize an SPF Record to Validate Outbound Email Sent from Your Domain. Source The PBL helps networks enforce their Acceptable Use Policy for dynamic and non-MTA customer IP ranges. Friday, May 22, 2009 5:10 PM 0 Sign in to vote go to http://www.spamhaus.org/pbl/

You're not using mapi ? 550 5.7.1 Unable To Relay (in Reply To Rcpt To Command) I have been racking my brain to figure this out and changing the SMTP authentication worked. I know it is something related to Exchange 2003, but none of the answers I've seen posted actually address the problem.

That would be the easiest solution - make sure this user is indeed submitting over port 587 (like possibly the rest).   Otherwise it's going to be pretty complicated, as it

I did a google search and found this forum. I was trying to use the virtual SMTP server in exchange so our Marketing department can send/receive email from a [email protected] address as well as with thier own email address. All Rights Reserved. Server Error '550 5.7.1 Relaying Denied If you're using your ISP as a email provider it may check that you're logged into the internet using them.

Any ideas? This is what I did Go to Account settings... Get the latest updates first * Blog| Why?| Partner| Terms| Privacy| Customers| Free Email Templates| Webinars| Tech Spec| GroupMail Touch| Mac| AboutCopyright © 1997 -Groupmail Ltd. http://mixtecadigital.com/unable-to/unable-to-relay-error.html Required fields are marked *Name Email Website Latest Posts Facts to Consider while Migrating Public Folders to Exchange 2013 How to Migrate Single or Multiple Exchange Mailboxes to Office 365 Repairing

THANK U V.MUCH THE ABOVE PROCEDURE SUPPORTED ME AND NOW I ABLE TO SEND THE MAIL FROM MY SERVER.....REGARDS Tuesday, June 01, 2010 11:38 AM 0 Sign in to vote permit Enter the relay name & select the suitable option from the dropdown list "Select the intended use for this Receive connector" Go to the ‘Local Network settings' tab and enter your If you’re sending to a large distribution group    - Groups with more than 5,000 members have the following three restrictions automatically applied: You must be a member of the group in Either you don't have a PTR record for your IP address, the name returned by the PTR lookup is different to the name your server sends in the HELO\EHLO commnad, or

Try this: Get-receiveconnector | fl name,bindings,PermissionGroups There's a group called ExchangeClients. The MX record for a domain that's enrolled in Exchange Online uses the syntax .mail.protection.outlook.com. Add SPF (Sender Policy FrameWork) record in DNS 2. Any thoughts on what might be causing this?